How To Change Tumbler On Desk Draw Lock

How to Remove Lock Cylinder From Desk-jump Drawer

There may come a time when y'all need to remove the lock cylinder from your desk-bound-bound drawer. Peradventure yous take lost your fundamental, or peradventure yous desire to alter the locks. Whatsoever the reason, at that place are a few unproblematic steps that you lot tin tin can accept to remove the lock cylinder without causing whatsoever damage. This article will talk over how to remove lock cylinder from desk-bound drawer.

How to Remove Lock Cylinder From Desk Drawer

Many older desk-jump drawers take a minor lock cylinder fastened to the desk's drawer. The lock cylinder may exist outside the drawer or inside the drawer. These locks were probable used to protect money and valuables from prying optics.

Push/Pin tumbler lock
Push tumbler lock removal tools
An empty paper towel curlicue or another tube
A screwdriver with a T6 Torx head bit
I rubber band
A set of pliers

A Stepwise Guide on How to Remove Lock Cylinder From Desk Drawer

Stride one: Decide How the Lock Works

The kickoff thing you lot volition have to practice is determine how your desk-bound drawer lock works. Y'all volition demand to know whether information technology's a pin tumbler or a button tumbler lock. Pin tumbler locks are detected by two small-scale holes drilled into the metal of the lock cylinder, whereas push button tumblers take a circular crash-land on their side. As well, if any other buttons or pins are in place, data engineering might exist challenging to open up the lock, particularly if they block admission to the screws that concur the lock together.

Footstep 2: Open upwards Your Desk Drawer And Examine How The Lock Is Congenital Into Information technology

At present that you know what kind of lock your desk drawer has, starting time opening it up. How you lot do this may vary depending on the type of lock, so information technology might exist challenging to open your drawer if screws are holding information technology together. Please note how the lock is fastened to the within of your desk drawer and what parts come into contact with each other (the forepart housing lock cylinder towards the dorsum, metal rods that adhere them, etc.

Step three: Decide Which Parts Y'all lot Will Have To Remove

Based on what you saw after opening up your desk-bound drawer, there are just a few parts that yous will accept to remove. The screws that secure these parts together are ordinarily hidden under plastic caps, which you can pop off with your fingers or pliers.

Withal, when removing these parts, be conscientious non to lose any of them, peculiarly if they are modest pieces like pins and springs. Instead, employ tweezers to agree onto them then they won't get lost. Also, remember how they were arranged inside the lock, so yous'll know where each part goes when assembling information technology over again later on.

Pace 4: Loosen the Screws

The next affair yous volition demand to do is remove any screws in place. They will nigh probable be located on the dorsum of the lock cylinder underneath where it was drilled into identify. If there are whatsoever other pins or buttons, they should exist removed at this indicate, as well, with a pocket-size screwdriver. Exist careful not to harm the metallic effectually where the pivot/button heads are through trying to excerpt them; otherwise, new holes will take to be drilled, compromising your lock's security further down the line.

Stride five: Look for Numbers on Back of Lock Cylinder

Later all of your pins and buttons have been removed, agree your lock upwards to look straight at its back. Yous should exist able to come across a series of numbers and letters which will wait something like this:

3 –> five –> eight–> one –> four

If there are only 2 rows of numbers, you demand to observe a lock choice with a T6 Torx caput bit that matches upwards with them and insert it into your lock cylinder. If there are three different rows, y'all might need to drill out the lock cylinder or buy some other ane birthday.

Stride vi: Remove The Lock Cylinder From the Desk Drawer

Once you have all of the necessary parts, data technology'south time to remove the lock cylinder from your desk drawer. You demand an empty newspaper towel curlicue or another tube and a rubber ring to practise this.

First, have one finish of your safe band and put data applied science into one finish of the paper towel whorl/tube, then stretch it out and then that it can become in and out through the other side without breaking hands. And then set both ends onto either side of i office of your button tumbler lock (cull whatsoever function you lot like) where pins are inserted, for example.

Finally, pull both ends simultaneously towards opposite directions until they snap apart, allowing that part to slide out of place. One time yous've washed this for all parts, the lock cylinder should now be separated from the residual of its contents inside your desk-bound drawer.

Step 7: Open up Upward The Lock And Remove The Locking Mechanism

Have your screwdriver with the T6 Torx caput bit and insert it into either of the side holes of the lock cylinder. Brand sure yous cull 1 hole where pins are non inserted since this will affect how the locking mechanism is removed successfully.

At present turn clockwise slowly while advisedly holding onto either cease, starting with whichever you adopt so long as there's no pin stuck in them. Once all of the pins accept been pushed upward together, they should now exist able to slide out of place hands, so note which ones they were stuck in for reference when reassembling things subsequently on. Finally, don't forget to put those extracted pins dorsum inside their respective parts in the lock cylinder.

Now that you've successfully removed the locking mechanism, you lot can separate it from the residuum of the parts in your desk drawer lock cylinder by using tweezers or pliers. It's commonly stuck to 1 part, merely sometimes it may be hard to remove, and and so make certain to pull hard if this is the case. Just go on in mind where each part was positioned when taking it out considering reassembling them, subsequently on volition not be easy if they are mixed upwardly.

Pace eight: Open The Desk-bound Drawer With Your Lock Cylinder

Now that your quondam desk-bound drawer lock has been taken apart and no longer functions, all that's left is to insert your paper towel tube into either of the ii holes and pull your new lock cylinder out from its packaging.

Now position some paper towels around the rubber ring to absorber it as you button information applied science back into place confronting those pins belongings it in place earlier. Make certain that this office of your desk drawer lock is facing the right style and inserted, specially if some screws are blocking its path, like in my instance.

Also, brand sure that yous position all the other parts on top of each other inside i finish of your newspaper towel curlicue/tube first, and so button them dorsum into place with a screwdriver (or annihilation else) later on.

Your desk-bound drawer is set to exist locked with its new lock in one case once more! Ensure that y'all don't plough the key too hard in either direction when locking or unlocking; otherwise, data technology might fissure. In that location'south no demand to worry if this happens considering yous can use a pair of pliers to curve back into place gently. These steps will help in how to remove lock cylinder from desk drawer.

Additional Tips:

When removing the cylinder from a broken key, make sure you insert the new one and try it several times to make certain information technology works.
Unplug your desk-bound lamp when working with the drawer lock. If you take access to a power drill, utilize that instead of an electric screwdriver for added control.
Cylinders are cheap, and and so buy several but in case yous mess upward this projection or lose 1 while taking them autonomously. You tin can store these parts in dissever plastic bags to avert remixing them if you lot don't have old locks lying effectually anymore, non to worry! Locks are relatively inexpensive, so purchase five unlike types before starting this project if demand be.
Though most locks come out without likewise much effort, some can exist stubborn and accept upward to 30 minutes of prying.
If the screwdriver is challenging to motility through your lock cylinder, add together more than liquid (oil or WD-40) to information technology before applying more than pressure on the tool.
Make sure you lot have a screwdriver with a good handle, and so your paw doesn't balk up when removing stubborn locks.
If your lock cylinder still won't budge, endeavour filing downwardly the tip's size with sandpaper earlier using more force to pry information technology open upwardly.
A magnet can be used in identify of a screwdriver, though it's normally simply effective on smaller locks since larger cylinders are thicker.

You tin tin check information technology out to Cut a Lock Off of A Storage Unit of measurement

Conclusion

Nosotros promise you accept learned how to remove lock cylinder from desk drawer. Now that you take learned how to remove the lock cylinder from your desk drawer, y'all can experience safe and secure knowing that you can access your holding when you demand them. Think to always go along a spare key in a condom place in an emergency. Have fun using your new skills!